DQSPI FLASH Controller with Execute in place – XIP functionality (SINGLE, DUAL, QUAD and OCTAL SPI Bus Controller with Double Data Rate support)
The DQSPI is a revolutionary quad SPI designed to offer the fastest operations available for any serial SPI memory. It is flexible enough to interface directly with numerous standard product peripherals from several manufacturers. Moreover, the IP Core supports all 8, 16, 32 bit processors available on the market. The DQSPI is a fully configurable SPI master/slave device, which allows you to configure polarity and phase of serial clock signal SCK. It enables the microcontroller to communicate with fast serial SPI memories and serial peripheral devices. Moreover, it’s capable of interprocessor communications in a multi‐master system. A serial clock line (SCK) synchronizes shifting and sampling of information on four serial data lines. In the Single SPI mode, data is simultaneously transmitted and received, while in DUAL, QUAD and OCTAL SPI modes, data is shifted in or out respectively on two, four and eight data lines at once. Additionally, transfer speed can be doubled by using the DDR protocol (Double Data Rate) – this feature allows the DQSPI to transfer/receive data on both falling and rising edges of SCK. The DDR together with QUAD SPI transfer allow 8 bits of data to be sent/received within a single SCK clock cycle. This makes the DQSPI perfect for systems, where performance is essential, or where the code can be moved from non-volatile memory to fast RAM, or for systems where device size and cost are the key, or where the program code can be executed directly from non-volatile memory, using an approach known as Execute-in-Place. DCD’s IP Core is a technology independent design that can be implemented in variety of process technologies. The DQSPI system is flexible enough to interface directly with numerous standard product peripherals from several manufacturers. The system can be configured as a master or slave device. Data rates as high as CLK/2, when other vendors’ solutions offer just CLK/8. Clock control logic allows selecting clock polarity, phase and four fundamentally different clocking protocols, to accommodate most available synchronous serial peripheral devices. When the SPI is configured as a master, software selects bit rates for the serial clock. The DQSPI automatically drives selected by SSCR (Slave Select Control Register) slave select outputs (SS7O – SS0O), and addresses SPI slave device to exchange serially shifted data. Error‐detection logic is included, to support interprocessor communications. A write‐collision detector indicates when an attempt is made to write data to the serial shift register, while the transfer is in progress. A multiple-master mode‐fault detector disables DQSPI output drivers automatically, if more than one SPI device simultaneously attempts to become a bus master. The DQSPI supports two DMA modes: single transfer and multi‐transfer. These modes allow the DQSPI to interface to higher performance DMA units which can interleave their transfers between CPU cycles or execute multiple byte transfers. The DQSPI is fully customizable – it is delivered in the exact configuration to meet your requirements.
Watch the DQSPI presentation on DCD’s You Tube:
- Full duplex synchronous serial data transfer
- DMA support
- Support for various Bus Standards
- Single, Dual, Quad and Octal SPI transfer/reception
- Data Bus Size configuration to 8, 16 or 32 bits wide
- Master/SLave operations
- Multimaster system supported
- Optional FIFO size extension to 128, 256 or 512 Bytes/Words
- Maximum supported Flash address range – 32 bits
- Execute in place – XIP functionality support
- Up to 7 SPI slaves can be addressed
- Software Slave Select Output – SSO – selection
- Automatic Slave Select outputs assertion during each byte transfer
- System error detection
- Interrupt generation
- Bit rates generated as 1/ 2.. 255 of system clock.
- Four transfer formats supported
- Simple interface allows easy connection to microcontrollers
- Fully synthesizable, static synchronous design with no internal tri-states
The DSPI is a fully configurable SPI master/slave device, which allows you to configure polarity and phase of serial...
+ Master & Multi-master operations
+ 8 SPI slave select lines
+ System error detection
The DSPI_FIFO is a fully configurable SPI master/slave device, which allows you to configure polarity and phase of a serial...
+ Fully configurable SPI master/slave dev
+ Two modes of operation: SPI & FIFO
+ 8 SPI slave select lines
The DSPIS is a fully configurable SPI slave device, designed to operate with passive devices, like memories, LCD drivers etc. It allows...
+ Full duplex synchronous data transfer
+ Slave operation
+ Automatic read and write operations
The DQSPI is a revolutionary quad SPI designed to offer the fastest operations available for any serial SPI memory. It...
+ The fastest available operations
+ For any serial SPI memory
+ Supports all 8, 16, 32-bit CPUs